DAL-TEX Enterprises, Inc. | Decatur, TX | The Complete Source of Tooling Components Needs

TYPICAL TORQUE-OUT AND TENSILE LOADS

All tests run with bolt thread of sufficient length to insure full thread engagement of insert. Torque-out was
determined using a torque wrench on a bolt in conjunction with a bushing. The bushing's maximum outside diameter
was in all cases less than the insert outside diameter, thus only pure torque was recorded, not clamp-up. 
Torque-out was recorded at the point the insert rotated relative to the parent material. Tensile (pull-out) was
determined using a 20,000 lb. Baldwin Southwark tensile machine. Load was applied until the first indication of
insert movement was noted; at this point the pull-out value was recorded.
NOTE: The minimum distance that an insert can be installed relative to the edge of a material is dependent upon
the characteristics and type of print material involved. Most materials will require one (1) times the insert O.D.
for edge distance, as measured from the center of the installation hole. However, this can vary with material.

E-Z LOK
TYPICAL TORQUE-OUT AND TENSILE LOADS
MATERIAL TRADE NAMES				LEXAN		ZYTEL NYLON		GLASS FILLED EPOXY (GEE)		GLASS FILLED EPOXY (GEB)		PHENALIC-PAPER COMP. LAMINATE		"GLASTIC" GLASS REINFORCED PLASTIC
PART NO.	MATE- RIAL	SIZE	HOLE SIZE	TORQUE -OUT IN LBS.	TENSILE LBS.	TORQUE -OUT IN LBS.	TENSILE LBS.	TORQUE -OUT IN LBS.	TENSILE LBS.	TORQUE -OUT IN LBS.	TENSILE LBS.	TORQUE -OUT IN LBS.	TENSILE LBS.	TORQUE -OUT IN LBS.	TENSILE LBS.
652-03	BRASS	(4-40)	.156	14	80	22*	69	18	140	19*	180	10	100	11	105
652-03	BRASS	(4-40)	.158	13	69	14	57	15	117	14	139	-	-	-	-
652-03	BRASS	(4-40)	.160	6	40	6	32	10	70	9	80	-	-	-	-
652-03	BRASS	(4-40)	.162	5	20	4	14	7	33	6	64	-	-	-	-
652-03	CRES	(4-40)	.156	14	82	22*	71	20*	145	19*	182	-	-	-	-
652-03	CRES	(4-40)	.158	12	70	14	60	15	120	13	140	-	-	-	-
652-03	CRES	(4-40)	.160	7	35	8	35	11	70	9	85	-	-	-	-
652-03	CRES	(4-40)	.162	5	16	5	15	8	29	6	60	-	-	-	-
652-04	BRASS	(6-32)	.188	30	85	30	100	42*	230	45*	240	22	240	20	210
652-04	BRASS	(6-32)	.190	24	75	25	90	38	180	37	235	-	-	-	-
652-04	BRASS	(6-32)	.192	13	50	15	17	19	170	22	150	24	210	24	200
652-04	BRASS	(6-32)	.194	6	40	8	65	13	160	17	120	10	165	-	-
652-04	CRES	(6-32)	.188	30	93	30	122	42*	262	45*	240	-	-	-	-
652-04	CRES	(6-32)	.190	20	80	20	110	34	205	33	235	-	-	-	-
652-04	CRES	(6-32)	.192	15	70	16	90	21	195	24	145	-	-	-	-
652-04	CRES	(6-32)	.194	10	50	12	75	14	180	21	125	-	-	-	-
652-05	BRASS	(8-32)	.219	40	180	40	210	85*	300	85*	280	41	230	45	230
652-05	BRASS	(8-32)	.221	35	178	35	200	70	273	75*	208	-	-	-	-
652-05	BRASS	(8-32)	.223	22	130	25	160	51	235	72*	190	-	-	-	-
652-05	BRASS	(8-32)	.225	15	80	16	110	43	132	67*	165	-	-	-	-
652-05	CRES	(8-32)	.219	30	190	35	220	75	310	85*	281	-	-	-	-
652-05	CRES	(8-32)	.221	25	145	30	175	60	240	75*	200	-	-	-	-
652-05	CRES	(8-32)	.223	15	70	20	100	44	175	72*	192	-	-	-	-
652-05	CRES	(8-32)	.225	14	50	18	80	42	102	65	165	-	-	-	-
652-06	BRASS	(10-32)	.250	80	240	82	375	90*	420	110*	420	75	420	80	450
652-06	BRASS	(10-32)	.252	45	172	54	250	66	320	110*	405	-	-	-	-
652-06	BRASS	(10-32)	.254	27	105	26	160	38	175	110*	300	-	-	-	-
652-06	BRASS	(10-32)	.256	18	30	20	132	22	150	105	205	-	-	-	-
652-06	CRES	(10-32)	.250	85*	250	85	420	90*	510	110*	490	-	-	-	-
652-06	CRES	(10-32)	.252	59	220	61	265	76*	460	107	425	-	-	-	-
652-06	CRES	(10-32)	.254	31	122	32	175	41	310	111*	257	-	-	-	-
652-06	CRES	(10-32)	.256	25	42	21	140	24	280	105	240	-	-	-	-